|
|
Post by xtron on Jan 25, 2005 9:12:05 GMT -5
complicated
|
|
|
|
Post by TheGlove on Jan 25, 2005 15:56:29 GMT -5
pwned/10
very good, very very good...
|
|
|
|
Post by xtron on Jan 25, 2005 17:26:15 GMT -5
pwhed/10 h???h
|
|
Raven
Level 6: Carrier
Beware the quiet ones
Posts: 948
|
Post by Raven on Jan 25, 2005 18:51:02 GMT -5
@ Xtron: i dont know either
@ auris: Very interesting desighn for turrets. it is comlicated but it will be strong.
|
|
|
|
Post by xtron on Jan 25, 2005 20:49:19 GMT -5
pawned ???
|
|
Nox
Level 3: Assault Frigate
Posts: 38
|
Post by Nox on Jan 26, 2005 5:04:45 GMT -5
nice ideea !! but why not just cut a hole like you've done then make a barrel roll from paper the diameter of the hole glue the barrel roll on one side to the turret and the just stick it in the hole this way you have a turnable turret and you will also be able to take it of and not assamble all the turrets in place before you glue the underside of the ship
|
|
TonyG2
Level 5: Destroyer
Remember the Pegasus
Posts: 261
|
Post by TonyG2 on Jan 26, 2005 7:29:53 GMT -5
Nox
Not bad idea but where you have a turret on the underside of the ship, then you risk it falling out if its not secured.
I guess one way would be to glue the lower turrets into position and use your method for the upper turrets provided you dont mind the lower turrets not turning.
Wouldn't work for me as I usually pack the interior of the model with lots of extra thick card, corrugated packing material or artists mounting board, and with loads of cross braces for extra strength. Because of that, there would be no room for a lengthy tube to be inserted.
Still, not a bad alternative to Auris' method.
|
|
Auris
Level 5: Destroyer
Posts: 406
|
Post by Auris on Jan 26, 2005 9:13:31 GMT -5
|
|
Nox
Level 3: Assault Frigate
Posts: 38
|
Post by Nox on Jan 26, 2005 10:26:01 GMT -5
right but not if you do the diameter of the barrel almost exactly like the diameter of the hole i've used this metod for the turrets on my ships(battle ships) www.digitalnavy.com |
|
|
|
Post by xtron on Jan 26, 2005 17:32:02 GMT -5
i don't understand
|
|
|
|
Post by TheGlove on Jan 28, 2005 20:00:39 GMT -5
am i the only one who got it ?? the barrel is bigger than the hole, so there is no risk of it falling down
|
|
|
|
Post by xtron on Jan 29, 2005 0:10:32 GMT -5
forget it .....
|
|
Auris
Level 5: Destroyer
Posts: 406
|
Post by Auris on Feb 9, 2005 5:00:32 GMT -5
|
|
Duck
Level 3: Assault Frigate
Posts: 28
|
Post by Duck on Feb 9, 2005 17:07:24 GMT -5
I would like to know the scale the Destroyer you have printed out. I am guessing that the cutting mat scale is 1 cm3 = one square, but more than that I hestitat to guess.
On a more important note when do you estimate when will you be posting the A.I. for the turrets.
Thanks
P.S. I have a solution for finding magnets for turets. I have recieved adds for Pizza place in the mail on the advertisments were flexible plastic magnets. simple to cut up and cheap. That may solve peoples problems.
|
|
Raven
Level 6: Carrier
Beware the quiet ones
Posts: 948
|
Post by Raven on Feb 9, 2005 19:29:52 GMT -5
Taht A.I is looking better every time auris! now i want to build it myself. ;D
|
|
